Delta Faucet Repair Guide - Stem-Style Faucet Fix

Delta bathroom and kitchen faucets with two handles are often stem-style faucets that include a neoprene valve seat and spring. This is different from a true cartridge-style faucet, which closely resembles a stem faucet but does not have valve seats and springs.
A stem-style faucet features a neoprene valve seat and spring that fit into the water inlet port in the valve body. The stem is held into the body with a bonnet nut, and the handle fits onto the top of the stem. Leaks in this type of faucet can usually be fixed with a new neoprene valve seat and spring. However, you may also need to replace the entire stem if the handle is stiff when turning on the faucet, if there is a leak around the handle when the faucet is turned on, or if replacing the seat and spring doesn’t stop the leak.

Delta’s Lifetime Warranty Policy covers all parts and finishes of Delta faucets purchased from authorized Delta sellers. They are warranted to be free from defects in material and workmanship for as long as the original consumer purchaser owns the home in which the faucet was first installed. Delta will repair or replace the product, free of charge, during the applicable warranty period. Proof of purchase (original sales receipt) from the original purchaser must be shown to Delta for all warranty claims.

Before beginning the repair, place your hand under the drip from the faucet to determine whether the leak is on the hot or cold side. This tells you which side to fix first, but it’s possible that both sides are leaking. Look under the sink to locate the shutoff valve on the side of the faucet you will work on. Turn the handle clockwise until it stops to ensure the water is off. If there are no shutoff valves under the sink, turn off the water to the entire house at the home’s main shutoff valve, then turn on both sides of the faucet to relieve pressure in the supply lines.

According to the Delta website, you can find your model number by looking at the model identification tag located on the faucet’s supply line.

For the repair, you will need the following equipment and tools: Tongue-and-groove pliers or adjustable wrench, Screwdriver or Allen wrench. Materials required include: New rubber seat and spring (one set for each handle), Plumber’s grease, Replacement stem (as needed).

Instructions for repairing a leaky Delta faucet include removing the faucet handle by loosening it with either a screwdriver or an Allen wrench.

Accessing the Faucet Handle: You may need to remove a decorative cap from the top of the handle to access the handle screw. Lift the handle straight up to remove it from the faucet stem.

Removing the Bonnet Nut: Loosen the bonnet nut securing the faucet stem. Use tongue-and-groove pliers or an adjustable wrench to turn the nut counterclockwise. Unthread the nut completely and remove it from the stem.

Removing the Stem: Note the position of the stem before removing it. You must reinstall it in exactly the same position for the faucet to work properly. Stems usually have one or more tabs that fit into notches in the stem housing to help you align the stem, but you can still get the stem backward. It might be helpful to take a photo of the stem for reference. Remove the stem by pulling it straight up and out of its housing. Use pliers, if necessary, gripping just the spindle at the top of the stem.

Removing the Valve Seat and Spring: Look inside the stem housing and locate the neoprene valve seat in a hole at the bottom of the faucet housing. The valve seat is a small, black, rubber cap with a hole in the top. Sitting inside and below the seat is a small metal spring. Remove the seat and spring by inserting a small screwdriver or Allen wrench into the hole of the seat and pulling up both parts together. Note the spring’s orientation inside the valve seat. The spring should be slightly larger in diameter at the bottom than at the top—where it fits into the seat. You must install the new spring and seat with the same orientation.

Installing a New Seat and Spring: Fit the new seat and spring onto the end of a screwdriver or Allen wrench in the same position as the original seat and spring. Use the screwdriver or wrench to guide the spring and seat into the hole in the stem housing. They must fit all the way down into the hole. Remove the screwdriver or wrench and confirm the valve seat is positioned properly.

Reinstalling the Stem: Apply a small amount of plumber’s grease to the O-ring at the base of the valve stem. If desired, you can also replace the O-ring (which is sometimes included with stem-and-spring kits) or the entire stem. Fit the stem into its housing, aligning the tabs on the stem with the slots in the housing. Push the stem all the way down until it stops. Reinstall the bonnet nut and tighten it carefully with pliers or an adjustable wrench. Do not overtighten the nut, which can damage the stem housing.

Checking for Leaking and Reinstalling the Handle: Turn the water supply back on by opening the shutoff valve (under the sink) counterclockwise all the way until it stops or by turning the water back on at the main. Check for leaks around the faucet stem. If it leaks, tighten the bonnet nut until the leaking stops; again, be careful not to overtighten. Fit the handle onto the stem and secure it with the screw or setscrew.

When to Call a Professional: If you are not handy or not confident in your ability to repair or temporarily fix a leaky faucet, you should consider bringing in help.

If a leaking faucet has led to additional damage in the surrounding area, or if there is a possibility of a more significant underlying problem, it is crucial to seek professional assistance. Calling in a professional will help to effectively address and resolve the situation.

Repairing Leaky Delta Faucets: A Step-by-Step Guide

Leave a Comment Cancel Reply